Gas Treating and Sulphur Recovery Workshop - Poland - Fall 2019

 

Location: Poland
Venue: TBD
Date: 10/01/2019 to 10/03/2019
Cost: $2,100.00
Meal Included: no

Optimized Gas Treating, Inc.
Three-day Seminar
Where: Poland
When: Fall 2019


Presenters: TBD


Agenda


Day 1: Gas Treatment


  • 9:00 – 9:15 Opening Remarks [Institute for the Chemical Process of Coal]
  • 9:15 – 9:30 Introduction to Optimized Gas Treating, Inc.
  • 9:30 – 10:15 Mass Transfer Rate Model (Predictive power and scientific phenomenological basis) 
  • 10:15 – 10:30 Morning Break
  • 10:30 – 12:00 Amine Treating - Important Parameters 
  • 12:00 – 13:00 Lunch
  • 13:00 – 13:45 Amine Treating – Blended Amines 
  • 13:45 – 14:45 Amine Treating – Heat Stable Salts 
  • 14:45 – 15:00 Afternoon Break
  • 15:00 – 16:45 Acid Gas Enrichment and Selective Treating
  • 16:45 – 17:00 End of Day 1 Q&A

Day 2: Gas Treatment (Continued)


  • 9:00 – 9:30 MDEA and formulated MDEA based solvents for bulk and deep CO2 removal (Syngas and LNG)
  • 9:30 – 10:00 CO2 Capture — How it differs from traditional treating & unusual behaviors
  • 10:00 – 10:15 Morning Break
  • 10:15 – 11:30 Physical Solvents including HotPot and amine promoted HotPot 
  • 11:30 – 12:00 Glycol Dehydration including modeling Stahl columns
  • 12:00 – 13:00 Lunch
  • 13:00 – 13:45 Caustic Treating
  • 13:45 – 14:45 Corrosion
  • 14:45 – 15:00 Afternoon Break
  • 15:00 – 16:30 Sour Water Stripping including 2-stage stripping
    • i. Important parameters and differences from amine regeneration
    • ii. Tray efficiencies-the moving target
    • iii. Phenolic vs. Non-phenolic Water
      • 1. Common Contaminants
        • a. HCN
        • b. Phenols
        • c. Alkanolamines 
        • d. Alkali metal cations
        • e. Strong acid anions
        • f. Hydrocarbons
      • 2. Optimal caustic injection point
    • iv. Corrosion and metallurgy considerations 
    • v. 2-Stage Stripping  
  • 16:30 – 17:00 Gas Treating Wrap-Up, Q&A

Day 3 : Sulphur Recovery Units


  • 9:00 – 9:30 Claus Process Overview
  • 9:30 – 10:00 Feed Preparation
    • a. Refinery vs. gas plant feeds
    • b. Acid Gas knockout
    • c. Combustion air 
  • 10:00 – 10:15 Morning Break
  • 10:15 – 11:45 Reaction Furnace
    • a. Overview of one and two zone furnace designs
    • b. Ammonia destruction
    • c. BTEX & hydrocarbon destruction
    • d. CS2 formation 
  • 11:45 – 12:00 Waste Heat Boiler (Begin) 
  • 12:00 – 13:00 Lunch
  • 13:00 – 13:45 Waste Heat Boiler (Finish)
    • a. H2 & COS recombination reactions
    • b. Sizing & rating
    • c. Corrosion & reliability considerations
  • 13:45 – 14:15 Condenser
    • a. Sizing & rating
    • b. Turndown studies
    • c. Emphasis on differences vs. WHB
  • 14:15 – 15:00 Converter
    • a. Deactivation mechanisms
    • b. Interpreting temperature profiles
    • c. COS and CS2 hydrolysis
    • d. Catalyst types and selection parameters 
  • 15:00 – 15:15 Afternoon Break
  • 15:15 – 15:45 Sulphur Handling and Degassing
    • a. H2S and H2Sx solubility
    • b. Characteristics of liquid sulphur
  • 15:45 – 16:30 TGU Quench Columns
    • a. SO2 breakthroughs
    • b. pH – to control or not to control
  • 16:30 – 16:45 Integrating the SRU with Upstream and Downstream Amine Units 
  • 16:45 – 17:00 Closing remarks (Institute for the Chemical Process of Coal)

Register
 

Subscribe

View past issues of The Contactor™ and ProTips™.

Subscribe to:

 

Testimonials